Integer Values
From Macros Wiki
| Integer Values | Description |
|---|---|
| TYPE | |
| MILL_TYPE | |
| LATHE_TYPE | |
| TOOL_NUM | |
| CRC | |
| COOLANT | |
| CUT_TYPE | |
| REPEATS | |
| MTHREAD_TRAVERSE_CP1 | |
| MTHREAD_ID_OD | |
| MTHREAD_THREAD_DIR | |
| MTHREAD_RAPID_IN | |
| SURFACE_TYPE | |
| SURFACE_CUT_TYPE | |
| SURFACE_BACK_AND_FORTH | |
| SURFACE_LACE_CUT_DIR | |
| SURFACE_OUTPUT_PREF | |
| SURFACE_CUT_OPT | |
| SURFACE_OFFSET_SURFACES | |
| SURFACE_ONE_PASS | |
| SURFACE_CONSTRAIN | |
| SURFACE_RETRACT_OPTION | |
| SURFACE_STAY_IN_STOCK | |
| SURFACE_CLEAR_STOCK | |
| SURFACE_CLEAR_STOCK_TYPE | |
| SURFACE_CUT_OVER_EDGES | |
| SURFACE_SKIP_FLATS | |
| CURVE_CUT_DIR | |
| SURFACE_FLOW_MACH_DIR | |
| SURFACE_FLOW_MACH_Z_ORDER | |
| SURFACE_FLOW_TRAVEL_AROUND_MODE | |
| SURFACE_FLOW_CUT_TYPE | |
| SURFACE_INTERSECT_TYPE | |
| SURFACE_CUTS_TYPE | |
| SURFACE_PASSES_TYPE | |
| SURFACE_CLEANUP_TYPE | |
| SURFACE_PASSES_PER_SIDE | |
| LATHE_PREFER_CANNED | |
| LATHE_CLEAR_ID | |
| LROUGH_ROUND_CORNERS | |
| LROUGH_CUT_OFF | |
| LROUGH_CUT_DIR | |
| LROUGH_ENTRY_PERP | |
| LROUGH_EXIT_PERP | |
| LROUGH_ROUGH_TYPE | |
| LROUGH_CSS | |
| LROUGH_RAPID_STEP | |
| LROUGH_MONOTONIC | |
| LROUGH_AVOID_AIR | |
| LROUGH_XPLUS | |
| LROUGH_XMINUS | |
| LROUGH_ZPLUS | |
| LROUGH_ZMINUS | |
| LROUGH_AUTO_FINISH | |
| LROUGH_SPINDLE_DIR | |
| LROUGH_FINISH_LAST | |
| LROUGH_CENTER_OUT | |
| LROUGH_CONSTANT_STEP | |
| LROUGH_PECK | |
| LROUGH_PLUNGE_TYPE | |
| LROUGH_CONSTANT_PATH | |
| LROUGH_FIXED_SP | |
| LROUGH_NUM_PASSES | |
| LROUGH_SHIFT_SQUARE_CORNERS | |
| LROUGH_CLEANUP_PASS | |
| LROUGH_USE_DEFLECT_COMP | |
| LROUGH_DEFLECT_COMP_VAL | |
| LROUGH_MULTI_PASS | |
| LATHE_CUT_OTHER_SIDE | |
| LATHE_USE_AUTO_CLEAR | |
| LTHREAD_STYLE | |
| LTHREAD_CUT_DIR | |
| LTHREAD_CUT_TYPE | |
| LTHREAD_CSS | |
| LTHREAD_BALANCED_IN_FEED | |
| LTHREAD_ALTERNATE | |
| LTHREAD_LAST_CUT | |
| LTHREAD_NOMINAL_PITCH_INDEX | |
| LTHREAD_TAPER_INDEX | |
| LTHREAD_NUM_SPRING_PASSES | |
| LTHREAD_NUM_STARTS | |
| LDRILL_ENTRY | |
| FEED_CONNECT | |
| CRC_OFFSET | |
| LEN_OFFSET | |
| CUSTOM_CBSET | |
| PATTERN_ON | |
| PATTERN_INDEX | |
| ROUND_CORNERS | |
| ENTRY_PERP | |
| EXIT_PERP | |
| IGNORE_TOOLS | |
| DEPTH_FIRST | |
| FM_USE_SHAPE | |
| FM_HPLUS | |
| FM_VPLUS | |
| FM_MOVEH | |
| FM_BEFORE_ZIGZAG | |
| FM_BACK_AND_FORTH | |
| FM_TYPE | |
| ENTRY_TYPE | |
| START_ON_RIGHT | |
| RETRACTS | |
| HIT_PARALLEL | |
| STAY_CLEAR | |
| CUT_BACK | |
| SAME_STROKE | |
| FULL_DIA | |
| STEPOVER_FEED_LOCK | |
| CLEAR_FEED_LOCK | |
| SCALLOP_FEED_LOCK | |
| CLEAR_PERIPH | |
| CS_NUM | |
| PATH_CS | |
| POCKET_TYPE | |
| WALL_MODE | |
| PREFER_SUBS | |
| HIT_FLATS | |
| POCKET_ENTRY_RAMP_TYPE | |
| POCKET_ENTRY_HELIX_TYPE | |
| SURFACE_ENTRY_TYPE | |
| SURFACE_ENTRY_RAMP_TYPE | |
| PROG_STOP | |
| RAPID_IN | |
| MATERIAL_ONLY | |
| DRILL_TYPE | |
| DRILL_POS_APPROACH | |
| DRILL_CLEAR_PLANE | |
| WALL_STEP | |
| WALL_TOP_TO_BOTTOM | |
| WALL_SAME_DIR | |
| WALL_SAME_DCEP_SIDE | |
| WALL_SWEPT_POCKET | |
| WALL_SWEPT_ISLAND | |
| S_USE_ADV_TOL | |
| M_USE_ADV_TOL | |
| CUT_SIDE | |
| MD_FROM_TOOL | |
| MD_VARY_WITH_GEO | |
| MD_VARY_WITH_FEAT | |
| MD_RETRACT_LEVEL | |
| MD_PROCESS_LOAD_H1Z_FEAT | |
| CONTOUR_ENTRY_RAMP_TYPE | |
| CONTOUR_ENTRY_HELIX_TYPE | |
| WRAP | |
| WRAP_NUM_COPIES |
