Process Integer

From Macros Wiki
Jump to: navigation, search

Up

Parameter Description Version Number
TYPE Process type
MILL_TYPE Mill process type
LATHE_TYPE Lathe process type
ALLOW_TOOL 1=Allow, 0=No Tool 10.9.13
TOOL_NUM Tool number
CRC CRC state
COOLANT Coolant type
CUT_TYPE Cut type
REPEATS Number of repeats
MTHREAD_TRAVERSE_CP1 Thread Mill traverse CP1
MTHREAD_ID_OD thread Mill ID or OD
MTHREAD_THREAD_DIR Thread Mill direction
MTHREAD_RAPID_IN Thread Mill rapid in
SURFACE_TYPE Surface process type
SURFACE_CUT_TYPE Cut type
SURFACE_BACK_AND_FORTH Back and Forth setting
SURFACE_LACE_CUT_DIR Lace cut direction
SURFACE_OUTPUT_PREF Output preference
SURFACE_CUT_OPT Cut option
SURFACE_OFFSET_SURFACES Offset surfaces
SURFACE_ONE_PASS One pass
SURFACE_CONSTRAIN Contrain state
SURFACE_RETRACT_OPTION Retract option
SURFACE_STAY_IN_STOCK Stay in stock
SURFACE_CLEAR_STOCK Clear stock
SURFACE_CLEAR_STOCK_TYPE Stock type
SURFACE_CUT_OVER_EDGES Cut over edges
SURFACE_SKIP_FLATS Skip flats
CURVE_CUT_DIR Cut direction
SURFACE_FLOW_MACH_DIR machining direction
SURFACE_FLOW_MACH_Z_ORDER Z order
SURFACE_FLOW_TRAVEL_AROUND_MODE Travel around mode
SURFACE_FLOW_CUT_TYPE Cut type
SURFACE_INTERSECT_TYPE Intersection type
SURFACE_CUTS_TYPE Cut type
SURFACE_PASSES_TYPE Passes type
SURFACE_CLEANUP_TYPE Cleanup type
SURFACE_PASSES_PER_SIDE Number of passes per side
LATHE_PREFER_CANNED Prefer canned option
LATHE_CLEAR_ID Clearance ID
LROUGH_ROUND_CORNERS Round corners
LROUGH_CUT_OFF Cut off
LROUGH_CUT_DIR Cut direction
LROUGH_ENTRY_PERP Entry perpendicular
LROUGH_EXIT_PERP Exit perpendicular
LROUGH_ROUGH_TYPE Rough cycle type
LROUGH_CSS Constant surface speed
LROUGH_RAPID_STEP Rapid step
LROUGH_MONOTONIC Is cycle path monotonic
LROUGH_AVOID_AIR Avoid air
LROUGH_XPLUS Cut in X plus direction
LROUGH_XMINUS Cut in X minus direction
LROUGH_ZPLUS Cut in Z plus direction
LROUGH_ZMINUS Cut in Z minus direction
LROUGH_AUTO_FINISH Auto finish option
LROUGH_SPINDLE_DIR Spindle direction
LROUGH_FINISH_LAST Finish last cut
LROUGH_CENTER_OUT Cut from center outwards
LROUGH_CONSTANT_STEP Constant step
LROUGH_PECK Peck value
LROUGH_PLUNGE_TYPE Plunge type
LROUGH_CONSTANT_PATH Constant path
LROUGH_FIXED_SP Fixed start point
LROUGH_NUM_PASSES Number of passes
LROUGH_SHIFT_SQUARE_CORNERS Shift square corners
LROUGH_CLEANUP_PASS Use a cleanup pass
LROUGH_USE_DEFLECT_COMP Use deflect compensation
LROUGH_DEFLECT_COMP_VAL Deflect compensation value
LROUGH_MULTI_PASS Multi pass
LATHE_CUT_OTHER_SIDE Can cut other side
LATHE_USE_AUTO_CLEAR Use auto clearance
LTHREAD_SHAPE_METHOD 0=From Parameters, 1=From Shape 12.0.36
LTHREAD_STYLE Threading style
LTHREAD_CUT_DIR Cut direction
LTHREAD_CUT_TYPE Cut type
LTHREAD_CSS Constant Surface Speed
LTHREAD_BALANCED_IN_FEED Balanced in-feed
LTHREAD_ALTERNATE Alternate cuts
LTHREAD_LAST_CUT Last cut
LTHREAD_NOMINAL_PITCH_INDEX Nominal pitch index
LTHREAD_TAPER_INDEX Taper index
LTHREAD_NUM_SPRING_PASSES Number of spring passes
LTHREAD_NUM_STARTS Number of thread starts
LDRILL_ENTRY Lathe drill entry
FEED_CONNECT Use feed connect
CRC_OFFSET CRC offset number
LEN_OFFSET Length offset number
CUSTOM_CBSET Custom CBSET
PATTERN_ON Use a pattern
PATTERN_INDEX Pattern index
ROUND_CORNERS Round corners option
ENTRY_PERP Entry perpendicular
EXIT_PERP Exit perpendicular
IGNORE_TOOLS Ignore tools
DEPTH_FIRST Cut depth first
SPRING_PASSES Number of spring passes
FM_USE_SHAPE Use shape
FM_HPLUS H Plus value
FM_VPLUS V Plus value
FM_MOVEH Move Horizontal
FM_BEFORE_ZIGZAG Before ZigZag
FM_BACK_AND_FORTH Back and Forth
FM_TYPE FM type
ENTRY_TYPE Entry type
START_ON_RIGHT Start on the right
RETRACTS Use retracts
HIT_PARALLEL Hit parallel
STAY_CLEAR Stay clear
CUT_BACK Cut back
SAME_STROKE Same stroke
FULL_DIA Full diameter
STEPOVER_FEED_LOCK Stepover feed lock
CLEAR_FEED_LOCK Clear feed lock
SCALLOP_FEED_LOCK Scallop feed lock
CLEAR_PERIPH Clear periphery
CS_NUM CS number or process
PATH_CS CS number of toolpath
POCKET_TYPE Pocket type
WALL_MODE Wall mode
PREFER_SUBS Prefer subs option
HIT_FLATS Hit flats option
POCKET_ENTRY_RAMP_TYPE Ramp type
POCKET_ENTRY_HELIX_TYPE Helix type
SURFACE_ENTRY_TYPE Entry type
SURFACE_ENTRY_RAMP_TYPE Ramp type
PROG_STOP Program stop
RAPID_IN Rapid in
MATERIAL_ONLY material only cutting
DRILL_TYPE Drill type
DRILL_POS_APPROACH Drill position approach
DRILL_CLEAR_PLANE Drill clearance plane
WALL_STEP Wall step
WALL_TOP_TO_BOTTOM Top to Bottom
WALL_SAME_DIR Same direction
WALL_SAME_DCEP_SIDE Dcep side
WALL_SWEPT_POCKET Swept pocket
WALL_SWEPT_ISLAND Swept island
S_USE_ADV_TOL Use advance tolerance
M_USE_ADV_TOL Use advance tolerance
CUT_SIDE Cut side
MD_FROM_TOOL Modify depth from tool
MD_VARY_WITH_GEO Vary with geometry
MD_VARY_WITH_FEAT Vary with feature
MD_RETRACT_LEVEL Retract level
MD_PROCESS_LOAD_H1Z_FEAT Load H1 Feature Z
CONTOUR_ENTRY_RAMP_TYPE Ramp type
CONTOUR_ENTRY_HELIX_TYPE Helix type
CONTOUR_RAMP_DOWN 1=Ramp Down 10.5.18
CONTOUR_NUM_EXTRA_OFFSETS Number of extra offsets 10.5.18
POCKET_OUTER_AS_BOSS 1=Outer as Boss 10.5.18
WRAP Wrap toolpath
WRAP_NUM_COPIES number of copies
DRILL_BORE_CUT_TYPE Cut type
ADV_EXIT_SAME_AS_ENTRY 1=Exit values are same as entry 10.2.22
ADV_ENTRY_TYPE Entry type 10.2.22
ADV_EXIT_TYPE Exit type 10.2.22
ADV_LINE_ENTRY_USE_CRC 1=Line Entry uses CRC 10.2.22
ADV_LINE_ENTRY_USE_OFF_PART_LINE 1=Line Entry uses Off Part Line 10.2.22
ADV_LINE_ENTRY_USE_RAMP 1=Line Entry uses Ramp 10.2.22
ADV_LINE_ENTRY_RAMP_INCLUDE_LINE 1=Line Entry Ramp uses Include Line 10.2.22
ADV_LINE_EXIT_USE_CRC 1=Line Exit uses CRC 10.2.22
ADV_LINE_EXIT_USE_OFF_PART_LINE 1=Line Exit uses Off Part Line 10.2.22
ADV_LINE_EXIT_USE_RAMP 1=Line Exit uses Ramp 10.2.22
ADV_LINE_EXIT_RAMP_INCLUDE_LINE 1=Line Exit Ramp uses Include Line 10.2.22
ADV_ARC_ENTRY_USE_CRC 1=Arc Entry uses CRC 10.2.22
ADV_ARC_ENTRY_USE_OFF_PART_LINE 1=Arc Entry uses Off Part Line 10.2.22
ADV_ARC_ENTRY_USE_RAMP 1=Arc Entry uses Ramp 10.2.22
ADV_ARC_ENTRY_RAMP_INCLUDE_RADIUS 1=Arc Entry Ramp uses Include Radius 10.2.22
ADV_ARC_EXIT_USE_CRC 1=Arc Exit uses CRC 10.2.22
ADV_ARC_EXIT_USE_OFF_PART_LINE 1=Arc Exit uses Off Part Line 10.2.22
ADV_ARC_EXIT_USE_RAMP 1=Arc Exit uses Ramp 10.2.22
ADV_ARC_EXIT_RAMP_INCLUDE_RADIUS 1=Arc Exit Ramp uses Include Radius 10.2.22
PROC_ID Process ID Number 10.2.22
LROUGH_USE_END_LIMIT lathe Rough uses End Limit 10.2.22
DRILL_REVERSE_ORDER Drill cycle has Reverse Order checked 10.2.22
BAXIS_USED B Axis Turning is used 10.2.22
BAXIS_METHOD B Axis Turning Method 10.2.22
BAXIS_MULTI_TRANS B Axis Turning uses multiple transitions 10.2.22
BAXIS_USE_MIN_ANGLE B Axis Turning Minimum Angle 10.2.22
BAXIS_USE_MAX_ANGLE B Axis Turning Maximum Angle 10.2.22
BAXIS_SMOOTH_CORNERS B Axis Turning uses Smooth Corners option 10.2.22
BAXIS_VECTOR_TYPE B Axis Turning Vector Type 10.2.22
BAXIS_CHECK_COLLISIONS B Axis Turning uses Collision Checking 10.2.22
UTIL_TYPE Utility Process Type 10.2.22
THREAD_MILL_RAPID_TO_FROM_CLEAR 1=Rapid to/from Clearance Diameter 10.3.11
THREAD_MILL_PLUNGE_AT_CENTER 0=Plunge at center, 1=Plunge at Diameter 10.3.11
THREAD_MILL_VARY_WITH_GEO 1=Vary depth with geometry 10.3.11
THREAD_MILL_ENTRY_EXIT_METHOD Entry/Exit method 10.3.11
THREAD_MILL_ENTRY_EXIT_RAD Entry/Exit radius 10.3.11
THREAD_MILL_CUT_TYPE 0=One Top Pass, 1=One Finish Pass, 3=Const Cut 3=Const Load 10.3.11
THREAD_MILL_DO_LAST_CUT 1=Specify exact depth of last cut 10.3.11
THREAD_MILL_NUM_SPRING_PASSES Number of Spring Passes 10.3.11
THREAD_MILL_START_DEPTH_TYPE 0=Abs Z, 1=Top of Hole, 2=Seg Start, 3=Seg End 10.3.11
THREAD_MILL_END_DEPTH_TYPE 0=Top, 1=Chamfer, 2=Mid, 3=Bottom, 4=Seg start, 5=Seg end, 6=Abs 10.3.11
THREAD_MILL_START_SEGNUM Start Depth Segment Number 10.3.11
THREAD_MILL_END_SEGNUM End Depth Segment Number 10.3.11
THREAD_MILL_SEGMENT_MATCH 1=Use Segment Matching 10.3.11
THREAD_MILL_SEG_MATCH_LEN 1=Match Segment Length 10.3.11
THREAD_MILL_SEG_MATCH_DIA 1=Match Segment Diameter 10.3.11
THREAD_MILL_SEG_MATCH_TAPER 1=Match Segment Taper 10.3.11
THREAD_MILL_SEG_MATCH_METHOD 1=Match Segment Method 10.3.11
THREAD_MILL_DIM_FROM_TOOL 0=Dimension from Hole, 1=Dimension from Tool 10.3.11
THREAD_MILL_BOTTOM_UP 0=Top down, 1=Bottom Up 10.3.11
MULTI_SHAPE_SINGLE_SHAPE_USE_MARKERS 1=Use Markers, 0=Do not use markers 12.0.28
MULTI_SHAPE_CENTERLINE 1=Use Markers, 0=Do not use markers 12.0.28
MULTI_SHAPE_CLOSED_INSIDE 1=Tool inside, 0=Tool outside 12.0.28
MULTI_SHAPE_CLOSED_ALTERNATE_SIDES 1 = Alternate tool side for nested shapes 12.0.28