Difference between revisions of "SET PROFILER MARKERS"

From Macros Wiki
Jump to: navigation, search
(Created page with "{{Command|syntax=SET_PROFILER_MARKERS <shape number> <side> <start feature> <start dist> <end feature> <end dist> <dir> <single feature> |description=:Set the prfoiler shape ...")
 
Line 1: Line 1:
{{Command|syntax=SET_PROFILER_MARKERS <shape number> <side> <start feature> <start dist> <end feature> <end dist> <dir>  <single feature>
+
{{Command|syntax=SET_PROFILER_MARKERS <shape number> <side> <start feature> <start dist> <end feature> <end dist>  <single feature>
 
|description=:Set the prfoiler shape markers to be used by a contouring process.
 
|description=:Set the prfoiler shape markers to be used by a contouring process.
  
 
|param2=<shape number>|param1_desc=Shape number.
 
|param2=<shape number>|param1_desc=Shape number.
|param2=<side>|param2_desc=Tool side (0 = center, 1 = left, 2 = right).
+
|param2=<side>|param2_desc=Tool side (0 = left, 1 = right).
 
|param3=<start feature>|param3_desc=Start feature (1 = first feature in the shape, 2 = second)
 
|param3=<start feature>|param3_desc=Start feature (1 = first feature in the shape, 2 = second)
 
|param4=<start dist>|param4_desc=Distance along the start feature (0.0 = start, 1.0 = end).
 
|param4=<start dist>|param4_desc=Distance along the start feature (0.0 = start, 1.0 = end).
 
|param5=<end feature>|param5_desc=End feature (1 = first feature in the shape, 2 = second)
 
|param5=<end feature>|param5_desc=End feature (1 = first feature in the shape, 2 = second)
 
|param6=<end dist>|param6_desc=Distance along the end feature (0.0 = start, 1.0 = end).
 
|param6=<end dist>|param6_desc=Distance along the end feature (0.0 = start, 1.0 = end).
|param7=<dir>|param7_desc=Direction (0 = same direction as the shape, 1 = opposite direction).
+
|param7=<single feature>|param7_desc=Single Feature (1 = yes, 0 = no).
|param8=<single feature>|param8_desc=Single Feature (1 = yes, 0 = no).
 
 
}}
 
}}
  
 
===Example===
 
===Example===
:SET_PROFILER_MARKERS 4, 1, 3, 0.2, 6, 0.8, 0, 0
+
:SET_PROFILER_MARKERS 4, 1, 3, 0.2, 6, 0.8, 0
  
 
[[Category:Profiler]]
 
[[Category:Profiler]]

Revision as of 15:09, 28 September 2012

Command

SET_PROFILER_MARKERS <shape number> <side> <start feature> <start dist> <end feature> <end dist> <single feature>


Set the prfoiler shape markers to be used by a contouring process.

Parameters

Shape number.
<side>
Tool side (0 = left, 1 = right).
<start feature>
Start feature (1 = first feature in the shape, 2 = second)
<start dist>
Distance along the start feature (0.0 = start, 1.0 = end).
<end feature>
End feature (1 = first feature in the shape, 2 = second)
<end dist>
Distance along the end feature (0.0 = start, 1.0 = end).
<single feature>
Single Feature (1 = yes, 0 = no).

Example

SET_PROFILER_MARKERS 4, 1, 3, 0.2, 6, 0.8, 0